General purpose
Sort by:
Baldor EHM4102T
$5,770.00
Baldor EHM4103T
$3,623.43
Baldor EHM4103T-5
$3,623.43
Baldor EHM4104T
$4,293.81
Baldor EHM4104T-5
$4,293.81
Baldor EHM4110T
$5,603.58
Baldor EHM4110T-5
$5,603.58
Baldor EHM4111T
$6,522.57
Baldor EHM4115T
$6,102.83
Baldor EHM4115T-5
$6,102.83
Baldor ERHM3162TA
$1,262.61
Baldor ERM3158TA
$883.96
Baldor EHFM3211T-8
$767.40
Baldor EHFM3218T-8
$833.43
Baldor EHFM3311T-8
$1,211.40
Baldor RM3007A
$356.41
Baldor RM3108A
$540.35
Baldor RM3112A
$581.45
Baldor RM3116A
$605.70
Baldor RM3154A
$643.43
Baldor RM3157A
$737.76
Baldor AOM25904T
$3,543.25
Baldor AOM3454
$373.93
Baldor AOM3455
$586.84
Baldor AOM3458
$417.05
Baldor AOM3535
$617.83
Baldor AOM3538
$490.49
Baldor AOM3539
$665.67
Baldor AOM3542
$528.22
Baldor AOM3543
$684.53
Baldor AOM3546T
$549.11
Baldor AOM3554T
$571.34
Baldor AOM3556T
$694.64
Baldor AOM3558T
$605.70
Baldor AOM3607T
$794.35
Baldor AOM3611T
$710.13
Baldor AOM3614T
$852.29
Baldor AOM3615T
$821.30
Baldor AOM3617T
$1,344.81
Baldor AOM3702T
$2,040.12
Baldor AOM3704T
$1,067.22
Baldor AOM3705T
$2,230.11
Baldor AOM3708T
$1,527.39
Baldor AOM3710T
$1,053.07
Baldor AOM3714T
$1,276.08
Servo Lab Capabilities
We have documented 96 different Servo Manufacturer repair reports in our Database
We repair AC Servos, DC Servos, AC Spindles, and AC Actuators
Capable of 24-hour repairs in many cases
We have thousands of spare and rebuilt motors in our inventory for parts or exchange motorsServo Lab Repair Procedures
-
Data
Motor nameplate data is recorded
-
Inspection
A visual inspection of any damage to the motor.
We check for- Damaged Leads/Terminals
- Worn output shaft/keyways
- Cracks in end bells or covers
-
Job Ticket
We complete to full write up off all motor data
Including- All winding tests (Resistance, Meg Ω, Continuity)
- All bearing sizes
- All seal sizes
- Brake torque tests (Record Torque, winding resistance)
- Feedback Tests (Tachometer/Encoder)
-
Motor Disassembly
- Bearing and seal sizes are recorded
- Bearing fits are measured on shaft and End bell
- Brake torque is measured as well as resistance and Meg Ω
- More winding tests are performed (Surge and HiPOT tests)
- Stator is then washed and baked in oven
- Magnets are inspected for cracks or if loose on shaft
- Encoder is tested with either (Heidenhain PWM20, Sick PGT-11, or Mitchell Electronics equipment)
-
Assembly
- New bearings are installed
- New seals are installed
- If required, new windings are impregnated
- Brakes are rebuilt or replaced depending on manufacturer design.
- Rebuilt or New encoders are installed and aligned using:
- (Heidenhain PWM20, Sick PGT-11, or Mitchell Electronics equipment)
-
Rotor Balancing and Testing
- Rotor is run through a full vibration diagnostic
-
Run Testing
- Every Motor is Run for a minimum of 1 hour using one of our drives.
- We use Siemens S110, S120, IndraDrive, AB Kinetix 300, Yaskawa 7, and AMC drives
-
Service Report
- A Final 3-page Service Report is filled out
- Pinout diagram for power and feedback is provided
- Brake torque is recorded a final time for our Service Reports
- A photo of nameplate and motor is attached
- A motor tag is installed on motor with QR code linking Service Report and Job Histories
- If requested, a YouTube link is attached to the service report of motor
A&C Electric is a certified distributor service center.